SKF Mud Scraper (KIT-MS50M)
SKF Mud Scraper is a removable dried mud scraper made of SKF proprietary low friction, low wear material named X-ECOPUR. Product can be easily installed and removed by end consumer. Forks removal from the triple clamps is not required. Product is designed to work over OEM forks wear rings and is compatible with OEM dust seals. However SKF recommends application with SKF fork seals kit for the lowest friction possible experience.
Due to the extensive years of research and development SKF products are the most technologically advanced and this is the standard that has been set for industry. Each part produced by SKF compliments the next. Stand-alone performance is superior but when several products are brought together the benefits are second to none. As the products are all designed to increase performance of the motorcycle, made from the most robust materials and are created with greater protection to make service intervals longer due to state of the art engineering and manufacturing.
- RRP $49.95
- $49.95
- In Stock: 20
The product’s objective is to protect the fork seals from being damaged by small debris and dried mud which are the real killer of oil seal lips. The dust seal is designed to keep out as much water as possible; small particles; powder and liquid mud. Unfortunately, in many riding circumstances, liquid mud may have enough time to dry over the lower part of the chrome tube.
Think about when you ride in muddy trails or tracks and than you pass through a fast section or you just stop for a few minutes to relax. During this time, mud left over the tubes has time to dry. As soon as you get back on the bike, the first jump landing or hard braking your forks will dive seals down into the section where the mud has accumulated and dried. Dirt particle will not move passing through the dust seal (which is not designed to scrape but to wipe!) and most likely will damage your oil seal lip triggering leakage.
The Mud Scraper is designed to scrape! It will constantly clean your tubes removing hard, dried particles leaving the dust seal the job of keeping out water and powder.
PART NUMBER : KIT-MS50KM
Usage recommendations
- Product should be only used when riding in extreme wet-muddy conditions
- Product should not be used in dry riding conditions. Using the product in dry conditions will not affect product performance or durability
- Check for interference with your hole shot device where applicable
- Check for interference with non-OEM fork protection shields.
- Product shall be placed over OEM outer tube steel wear rings (with except of WP forks). Please check your steel wear rings are in good conditions. Should they be worn they may affect the capacity of the mud scraper to stay fixed over the forks
- Product shall not be used in conjunction with other seal savers products
- Remove SKF Mud Scraper after riding and properly clean with water
Application:
- HUSQVARNA CR125 2007-2009
- HUSQVARNA TC250 2006-2009
- HUSQVARNA TC450 2006-2009
- HUSQVARNA WR125 2007-2010
- HUSQVARNA WR250 2007-2010
- HUSQVARNA WR300 2007-2010
- HUSQVARNA TE250 2007-2009
- HUSQVARNA TE450 2006-2009
- HUSQVARNA TE510 2006-2009
- TM EN 125 2007-2015
- TM EN 250 2007-2015
- TM EN 250F 2007-2015
- TM EN 300 2007-2015
- TM EN 450F 2007-2015
- TM EN 530F 2007-2015
- TM MX 125 2007-2015
- TM MX 144 2007-2015
- TM MX 125 2007-2015
- TM MX 250 2007-2015
- TM MX 250F 2007-2015
- TM MX 300 2007-2015
- TM MX 450F 2007-2015
- TM MX 530F 2007-2015
- BETA RR 250 2T RACING 2005-2011
- BETA RR 350 4T RACING 2005-2011
- BETA RR 450 4T RACING 2005-2011
- BETA RR 525 4T RACING 2005-2011
Downloads
Shopping Cart
| Shopping cart is empty. |
All prices are listed in $AUD.
Member Options
